Product Introduction

FY-6KFG-S1/LV
The FY-6KFG-S1/LV is a 6 kW hybrid inverter with a rated AC output of 6,000W/6,000VA, single-phase 220/230/240V, L+N+PE. On the DC side, it uses a 48V low-voltage battery system, supporting lithium-ion and lead-acid batteries, with a battery voltage range of 40–60V. On the PV side, the maximum usable PV power is 9,000W, the maximum PV input voltage is 500V, the MPPT operating range is 60–450V, and it has one MPPT and one string, with a maximum input current of 36A. The maximum grid input power is 11,500W, and the maximum input current is 50A; the maximum grid passthrough power to the load is 9,000W. It supports parallel connection of up to 12 units, and the document notes that . The ingress protection rating is IP54, with DC/AC Type III SPD, and a 3-year warranty.
| Item | Parameter |
|---|---|
| Rated AC output | 6,000W / 6,000VA |
| Max. efficiency | 95% |
| Max. PV usable power | 9,000W |
| Max. PV input voltage | 500V |
| MPPT range | 60–450V |
| Max. PV input current | 36A, 1 MPPT/1 string |
| Battery type | Lithium-ion/Lead-acid |
| Nominal battery voltage | 48V, range 40–60V |
| Max. charge/discharge current | Specification table: 140A/140A; promotional page states 140A/160A, to be confirmed with the final specification |
| Max. grid input power | 11,500W |
| Max. passthrough power | 9,000W |
| Peak output | 200% @ 5.5s |
| Parallel capability | Up to 12 units; only the 6K model supports three-phase parallel operation |
| Transfer time | UPS typical 10ms; home appliance typical 20ms; parallel operation typical 50ms |
| Protection | IP54, DC/AC Type III SPD |
| Communication | USB OTG, RJ45 BMS CAN/RS485, parallel RJ45, dry contact, Wi-Fi/LAN optional |
| Warranty | 3 years |
Main Advantages
1. Strong PV oversizing capability, suitable for high-power modules
It supports 200% PV oversizing and 150% PV usable power, with a maximum usable PV power of 9,000W, providing a high oversizing margin relative to the 6kW rated output. The maximum PV input current is 36A, suitable for high-power solar panels and helping generation in the morning, evening, and low-light hours. Note, however, that it has only 1 MPPT and 1 string input, so module string design flexibility is limited.
2. High battery charge/discharge current, 48V low-voltage system
The maximum charging current is 140A; the specification table lists maximum charge/discharge at 140A/140A, while the promotional page mentions 160A discharge. High current facilitates fast charging and discharging and supports surge loads, but at 48V, 140A imposes high requirements on cables, breakers, and terminals, so installation must be designed for high current. Lead-acid battery support makes it suitable for low-cost replacement or lead-acid storage projects.
3. Strong AC input and passthrough capability
The maximum grid input power is 11,500W and the maximum input current is 50A, with maximum grid-to-load passthrough of 9,000W. There is ample margin for grid charging, large-load passthrough, and hybrid supply, making it suitable for homes with concentrated total loads or small shops.
4. Good backup power and surge-load capability
Peak output is 200% @ 5.5s, which can briefly support motor, water pump, compressor, and other startup surge loads; UPS typical transfer is 10ms, suitable for loads with certain requirements for outage transfer. However, continuous loads should still be designed at 6kW, and THD<3% is under linear load conditions.
5. Flexible parallel expansion and three-phase extension
Up to 12 units can be paralleled for single-phase capacity expansion; the document notes that only the 6K model supports a three-phase parallel system. This is attractive for users requiring gradual capacity expansion or small three-phase systems, but parallel transfer time is typically 50ms, and three-phase parallel systems must be designed according to the manufacturer's solution.
6. Multi-energy and smart load management
It supports an independent generator port and can form a hybrid system with a diesel/gasoline generator; dual output with smart load can prioritize critical loads and disconnect non-critical loads. Time-based battery charging/discharging supports peak-valley tariff arbitrage.
7. Intelligent O&M and protection
It supports USB OTG, BMS CAN/RS485, parallel communication, and dry contacts, with Wi-Fi/LAN optional; the promotional page states built-in Wi-Fi and Bluetooth for local and remote monitoring, but the specification table says Wi-Fi/LAN optional, so the specific version needs confirmation. IP54, DC/AC Type III SPD, overvoltage/overload/short-circuit/overtemperature protection, and EN/IEC 62109-1/-2 and EN/IEC 61000 certification, with a 3-year warranty, make it suitable for indoor and outdoor sheltered installation.
Application Scenarios

Residential PV storage and self-consumption
The 6kW single-phase output is suitable for main household loads; 9kW usable PV power and a 48V battery system are suitable for daytime PV charging and nighttime discharge, with time-based charging/discharging for peak-valley arbitrage.
Backup power and weak-grid areas
UPS typical 10ms transfer is suitable for backup power for home lighting, routers, refrigerators, water pumps, etc. The grid range is 170–280V in UPS mode and 90–280V in home appliance mode, providing good adaptability to weak grids, but the UPS-mode voltage range is narrower, so configuration must match the load type.


Off-grid/remote areas without electricity
It supports lead-acid and lithium batteries, a generator port, and dual output with smart load, suitable for areas without grid or with unstable grid. Lead-acid support lowers initial cost; smart load can prioritize critical loads.
Generator hybrid supply
The independent generator port is suitable for hybrid operation of diesel generators with PV and batteries, reducing generator runtime. It is suitable for farms, villas, communication sites, or remote shops.


Small commercial/shop load management
With 6kW rated output, 9kW passthrough, and 200% short-term peak, it is suitable for small shops, clinics, offices, etc. Dual output can separate non-critical loads such as air conditioners and freezers from critical loads such as lighting and cash registers.
Parallel expansion and small three-phase systems
When larger single-phase capacity is needed, up to 12 units can be paralleled; only the 6K model supports three-phase parallel operation, suitable for small three-phase loads or gradual expansion projects. However, parallel and three-phase parallel solutions must be designed according to the manufacturer's technical manual.

Regarding us
FY Solar - Full-Spectrum Solar & Energy Storage Partner | 10+ Years Factory Direct
Company Overview FY Solar is a vertically integrated solar energy and energy storage manufacturer with over 10 years of industry expertise. We own production lines for lithium batteries and solar panels under our proprietary brand, and serve as authorized distributors for select international brands - giving buyers access to the full solar value chain from a single, trusted source.
We specialize in serving distributors, wholesalers, solar installers, and EPC contractors who need competitive pricing, reliable supply, and professional technical support.
Manufacturing & Own Brand Two core product lines are manufactured in-house under our own brand:
Lithium Batteries: LiFePO4 chemistry, residential and commercial battery packs, scalable modular design for home, C&I, and off-grid applications. MOQ: 1 unit - the lowest barrier to entry for distributors testing new markets.
Solar Panels: Monocrystalline and bifacial modules, 100W–700W+. MOQ: 1 pallet (~20–31 panels depending on wattage) - ideal for small distributors and project-based procurement.
Factory-direct supply means: no middleman markup, direct quality control, and full OEM/ODM customization capability.
Our Certificate




Global Exhibitions

Hot Tags: 6kw hybrid inverter, China 6kw hybrid inverter manufacturers, suppliers, factory, 110v solar inverter, 8kw solar inverter, compact solar inverter, high efficiency solar inverter, solar inverter with app monitoring, solar inverter with cooling fan
